Dana 35 gear oil capacity.

Dana 30 - 1.25 quarts 80W-90 Dana 35 - 1.75 quarts 80W-90 or 75W-140 synthetic Dana 44 - 2 quarts 80W-90 or 75W-140 synthetic Rubi Dana 44 - 2 quarts 75W-140 synthetic Thats from a post wheelin98tj made link here click me365. Jan 14, 2011. #10. Believe owner's manual specifies, 50 weight engine oil. Has been a tad bit of improvements in gear box oils since 1966. Suggested reading is, ANSI/AGMA 9005-E02. As the Dana 20 has neither bronze synco rings, or friction surfaces, oils with extreme pressure additives will prove beneficial.Jan 12, 2008 · Fortune Favors the Brave. Feb 8, 2011. #2. oil weight must be hypoidal gear oil. 80w-90. my 7.5" diferential uses 2.5 quarts of oil. im not sure how much yours will need tho. Jeep Wrangler with M200 (DRZ) rear axle: Use 75W-140 GL-5 gear oil 6,8. Jeep Wrangler with Dana 44 axle: Use 80W-90 GL-5 gear oil 6. Always remember to check if your Jeep has a limited slip differential, as this may require an additional friction modifier additive 1,2. Differential Fluid Capacity

11 Apr 2015 ... ... Capacity Oil Drain Pan: https://amzn.to/2OjqXjh. ... Wrangler Rear Differential Fluid Change on the YJ (DANA 35) ... Manual Hard To Shift or Won't ...

Typically GL5 75W-90 or 75W-140 (heavy duty use) gear oil. If you have a limited slip diff you may need the friction modifier additive depending on the gear oil. The label should say if it is needed.

The Dana 60 spec is just under 3 quarts. In my personal experience, the Dana 50 will take about 2.5 - 2.75 quarts to fill to the plug. As far as I know, the D50 and D60 use the same case, so they SHOULD have the same capacity. Be warned though, if your inner axle seals are bad, overfilling will make that obvious.It depends on where you live and how you drive. In a hot place with no winter weather, you want a thicker oil, say a viscosity over 90. If a cold place then want a lighter oil below 90. If a lot of heavy and hot towing, then a heavier oil. It is just like motor oil. Hotter, go heavier. Colder, go lighter.Dana 35 Axle: 80W-90 Gear and Axle Lubricant: 3.5 Pints / 1.7 Liters: Dana 44 - Rear Axle: 80W-90 Gear and Axle Lubricant: 4.75 Pints / 2.25 Liters *Limited-Slip (Trac-lok) Rear Axles require the addition of 118 ml (4 oz.) Limited Slip Additive *75W140 Gear and Axle Lubricant Recommended For Towing: Brake Master Cylinder: DOT 3 Brake Fluid#2 · May 27, 2009. 1.75 quarts is the recommended fill capacity, but I just installed the rock crusher diff cover on mine and used two full quarts also.Definitely NOT a 10.5L Sterling, which makes the literature wrong. Looks like you need 4.0L of 75w-90 synthetic oil. Depending on brand you may need to add ~8 oz of friction modifier, Ford calls theirs XL-3. Some synthetic oils come with friction modifier, so you may not need it.

11 Apr 2015 ... ... Capacity Oil Drain Pan: https://amzn.to/2OjqXjh. ... Wrangler Rear Differential Fluid Change on the YJ (DANA 35) ... Manual Hard To Shift or Won't ...

I put in exactly recommend amount of 1.75 quarts. That amount barely fill up the bigger cover. Some recommend adding till fluid comes out of the filling hole. I just can't imagine added that much fluid. Has anyone who have bigger covers like Solid differential …

Husky's Mobile Job Box has a 25-gallon capacity and a large removable tray for storing power tools, hand tools, accessories and gear. Expert Advice On Improving Your Home Videos La...Even basic networking gear gets messy real quick, if the pile of unorganized cables under my desk right now is any indication. Mounting your hardware to a simple, wall or desk-moun...Ever since changing the gear ratio on my Dana 44 rear diff a couple of years ago from 3.55 to 4.10, the gears whine when going around 35-55 MPH with just enough throttle to maintain that speed. Not a loud whine, just enough to be annoying. When accelerating or decelerating in this range the whine disappears. At speeds above or below 35-55 there ...Summary: (1) front differential (D30) - the only lube recommended is synthetic 75W-140, although the 1999 does have an alternative of 80W-90. (2) rear D35C and D44A - 80W-90 except for towing and other heavy-duty uses when 75W-140 synthetic is recommended.Carrying capacity is the idea that sustainability requires balance. Learn about carrying capacity and human population. Advertisement ­­In 1798, an English clergyman named Thomas M...This will prevent any dirt from entering the housing and contaminating the gear oil. 4) Remove the fill plug and make sure that the gear oil is up to the bottom of the fill hole. ... Dana 35 SLA (1998-2011) The 1998 and newer Ford Ranger uses a different style front axle assembly than the 1983-1997 models. To check the fluid in these ...The Haynes manual says to use 75W-140 GL-synthetic. When I peruse the internet about Dana 60 open differential fluid, I see people saying varying things, including 80W90, 75W140 synthetic, 75W90 full-synthetic, etc, as well as varying brans (Mobil, Red Line, etc) being better and / or cheaper than Motorcraft.

Superior Axle & Gear offers its Super 35 kit and Warn has a full-float kit. The Super 35 kit is available for both C-clip and non-C-clip axles. The kit replaces the …Received 475 Likes on 422 Posts. NCM Sinkhole Donor. For gear oil, you can use a good grade of GL-5 rated 80W-90 (Valvoline is fine) and a bottle of the GM posi additive. Shouldn't take more than 2 quarts. For the driven gear, go to a reputable tranny shop or try the dealer. Just tell them you have 3.45 gears and you need the gear for a …Can't seem to find an exact spec . It is the Dana 70 with Limited slip my truck is in my sig. Thanx in advance for the help. 2002 2500 QC LB, 4x4, SLT Laramie. S&B CAI Silencer Ring MIA, Fass 150, AFE Bladerunner Intake Horn, MBRP 4" TB Exhaust Quadzilla Boost Fooler, BD APPS noise isolator, FOX 2.0 shocks and 34x12.50 Hankook DynaPro MT.Ring Gear and Pinion Note: Ring gear and drive pinion are matched parts and must be replaced in sets. 1 - Part number 2 - Number of ring gear teeth 3 - Manufacturing numbers 4 - Matching gear set number 5 - Number of pinion teeth 6 - Date code 7 - Indicates genuine Spicer parts 8 - Heat code SPICER 41-8 127381 NL2 OF 17 8-41 127428 SPICER 17 G ...The NLGI specs are important - typical NLGI GL-5 gear oil carries added sulphur used as an Extreme Pressure (EP) lubricant. Especially when heated, sulphur is antagonistic to yellow (copper-based) metals - and the synchronizer rings and any bushings in the AX-15 are bronze. ... -Dana 35 - 3.5 Pints (1.66L) SAE 75W-90-Dana 44 - 4.0 …

Cargo carrying capacity is something that all RV drivers and towers should know. Learn how to calculate your vehicle's cargo carrying capacity at HowStuffWorks. Advertisement Most ...

Agree 100% on synthetics for the diff after gear break-in and have been running syn Mobil-1 for years in all my vehicles. As for diff heat buildup, I'm a firm believer of adding a quality finned cast aluminum cover. Besides adding about 25% more oil capacity and having a convenient drain plug, they do a super job of dissipating heat.Lower your Jeep and fill up the oil reservoir with the recommended type and capacity of engine oil. ... Dana 30 - Front Axle: 80W-90 Gear and Axle Lubricant: 2.5 Pints / 1.2 Liters: Dana 35 Axle: 80W-90 Gear and Axle Lubricant: 3.5 Pints / 1.7 Liters: Chrysler 8.25 Rear Axle: 80W-90 Gear and Axle Lubricant:2003X. 4947 posts · Joined 2009. #6 · Jul 27, 2012. I just did mine a few months ago, need to do it again as my inner oil seal is leaking onto the knuckle. My HPD30 only took 1.5 Quarts before it spilled out of the fill hole. I have a UCF Cover. It seems low, but there are no strait answers on here. It has 4.88 gears.Models with Dana 44 axle: 80W-90 GL-5 gear oil; ... Dana 35: Commonly used in the rear axle of older Jeep Wranglers. While sturdy, it’s not as robust as the Dana 44 and may be a weak point for heavily modified vehicles. ... Typically, the front differential capacity is around 1-2 quarts, while the rear differential takes 1.4-1.5 quarts 3,8 ...226 RBI (Model 44) - Mopar® Gear Lubricant 80W-90 (Trailer Towing Mopar® Synthetic Gear Lubricant 75W-140) RUBICON 226 RBI (Model 44) - Mopar® Synthetic Gear Lubricant 75W-140. NOTE: Trac-lok® equipped axles require 118 ml (4 ounces) of Limited Slip Additive in the lubricant. SIRA 4x4 club. I'll be Savvy someday!Posts 13,886 Thanks 5 Location Stonelick Lake, Ohio Vehicle(s) 83 CJ7 350 tbi, TH350, D300 twin sticked & clocked, narrowed Chief D44 Eaton Elocker & Moser shafts, Explorer 8.8 Detroit locker, 410's, RE 4.5" spring lift 1" body lift, 35" Claws, cage tied to frame, Corbeau baja seats, HD tie rod and draglink, u-bolts flipped, custom skid plate …

hmskyles. 5 posts · Joined 2017. #5 · Oct 29, 2018. The rubicon e-lockers don't require friction modifier. Front JK Dana 44 = 1.35 quarts. Rear JK Dana 44 = 2.375 quarts. That's according to chrysler, I just changed the diff fluid in my 08 Rubi and it was pretty close to that amount with aftermarket diff covers. U.

XFE 75W-85: Available in 5-gallon containers. Spicer XFE 75W-85 synthetic gear lubricant is our most fuel-efficient lube to date. You can enjoy a 1.9% fuel savings improvement over standard FE 75W-90 oil and extend the warranty on your Spicer heavy-duty or medium-duty carriers. Improved fuel efficiency. Extended drain interval: up to 500,000 miles.

I replaced the OEM oil with Amsoil Severe Gear--75W-110 in the front and 75W-140 in the rear. It took 1.3QTs in the front and 1.6QTs in the rear. Off-Roading in my Wildtrak; taking a break from Wranglerville.The extended drain program and any extended warranty program are separate programs. Note: For specifi c detail on Dana extended warranty programs refer to the Dana Warranty Guide or call 1-877-777-5360. Note: For a complete list of Dana “approved lubricants” for extended drain, refer to Approved Lubricant Suppliers Manual, DALSM072012.For trailer towing, use MOPAR Synthetic Gear & Axle Lubricant (SAE 75W-140). Models equipped with Trac-Lok require an additive. 3.06 Pints/1.45 Liters 220 RBI (Model 44) Rear Axle – T/L MOPAR Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. For trailer towing, use MOPAR Synthetic Gear & Axle Lubricant (SAE 75W-140).Axle Differential (Front)We recommend you use Mopar Gear & Axle Lubricant (SAE 80W-90) (API GL-5).Axle Differential (Rear)226 RBI (Model 44)– We recommend you use Mopar Gear& Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. For trailer towing, use Mopar Synthetic Gear & AxleLubricant (SAE 75W-140). Models equipped with Trac …I have a factory Dana 44. I was wondering how oil it takes? Some say to fill it until it comes out the fill hole. When I went to 6" coils from 4" coils it changes the angle of the pumkin and decreases the amount of oil it can hold. I can only imagine how much less it was able to hold going factory height to 6" lift. A buddy told to put in 1.5 ...Front Axles Dana 30 2.5 pints Gear lube GL-5 80W-90 or 75W-140 synthetic: Rear Axles Dana 35 3.5 pints Gear lube GL-5 80W-90 or 75W-140 synthetic: D-44 Axle Front & Rear Gear lube 4.0 pints GL-5 80W-90 or 75W-140 synthetic, Rubicon - 75W-140 synthetic w/trac-lok add 4.0oz of Limited Slip Additive.4.0L Engine Oil: 6 Quarts / 5.7 Liters: 10w-30 or 5w-30: 4.2L Engine Oil: 2.5L Engine Oil: 4 Quarts / 3.8 Liters: 4.0L Coolant: 10.5 Quarts / 9.9 Liters: 50/50 Mixture of Antifreeze and water: 4.2L Coolant: 2.5L Coolant: 9.0 Quarts / 8.5 Liters: NV231 Transfer Case (Man Trans) 1.6 Quarts / 1.5 Liters: ATF 3 or ATF 4: NV 231 Transfer Case (Auto ...Dana 30 = 2.5 pints. Dana 35 = 3.5 pints. Dana 44 = 4.0 pints. *Engines: - 10w30 for good general usage in most climates. - 5w30 for those colder climates (when …San Antonio, TX. Jan 31, 2019. #2. According to Currie conventional gear oil is better at heat transference than synthetic (plus it's cheaper). 75 or 80W90 is good if you don't tow, otherwise a higher viscosity like 80W-120 or 85W-140 is good. If your Rubicon has the factory lockers then you don't need to add any friction modifier, otherwise ...TJ diff fluid. I am wanting to change the fluid in the front and rear diffs and I am not sure of the capacity or which axle I have. The front is stamped with DANA 40869-136-0 and the rear is DANA 43225-115-0. I am thinking the front is a Dana 35 and the rear is a Dana 44 but I might be wrong. It is a 2001 Sahara. The Ford Ranger 4x4 received a new SLA (Short arm Long Arm) suspension in 1998, and used that suspension until its production end in 2011. Unlike the reverse rotation Dana 35 used from 1990-1997, the Dana 35 SLA is a standard rotation axle. This means that the gears from a 1990-1997 Dana 35 will not work in a 1998-2011 Ford Ranger.

It is however a waste of money to use the synthetic fluid in the differentials. I also have a D44 LSD rear. I paid equivalent to less than $25 for enough 85W140 fluid for both differentials. Just to give you an idea the MOPAR 80W-90 was around $180 for the fluid for both here in SA. Share.TJ diff fluid. I am wanting to change the fluid in the front and rear diffs and I am not sure of the capacity or which axle I have. The front is stamped with DANA 40869-136-0 and the rear is DANA 43225-115-0. I am thinking the front is a Dana 35 and the rear is a Dana 44 but I might be wrong. It is a 2001 Sahara.Sent from my Autoguide iPhone app. Keep in mind a complete drain of a dana 70 if doing brakes and hub seal will take 3.5 + axle tube and hub cavity. I am using 50% Lucas and 50% 80/90 to refill my '68 Dana 70. It is a summer only driver. Like.Instagram:https://instagram. roto grip exotic gem reviewwichita ks chinese buffetkristina ellis husbandhow to make pimple stop bleeding I want to change oil in my differentials. Can I use 75w-140 oil in Dana 30 and 35 without vari-lok? How do I know if my diffs are limited slip? Thanks!Can't seem to find an exact spec . It is the Dana 70 with Limited slip my truck is in my sig. Thanx in advance for the help. 2002 2500 QC LB, 4x4, SLT Laramie. S&B CAI Silencer Ring MIA, Fass 150, AFE Bladerunner Intake Horn, MBRP 4" TB Exhaust Quadzilla Boost Fooler, BD APPS noise isolator, FOX 2.0 shocks and 34x12.50 Hankook DynaPro MT. identogo emsiregal tall firs Dana 30 - Front Axle: 80W-90 Gear and Axle Lubricant: 2.5 Pints / 1.2 Liters: Dana 35 Axle: 80W-90 Gear and Axle Lubricant: 3.5 Pints / 1.7 Liters: Chrysler 8.25 Rear Axle: 80W-90 Gear and Axle Lubricant: 4.4 Pints / 2.08 Liters: Dana 44 - Rear Axle: 80W-90 Gear and Axle Lubricant: 4 Pints / 1.89 Liters mississippi 4th stimulus check update Ring Gear and Pinion Note: Ring gear and drive pinion are matched parts and must be replaced in sets. 1 - Part number 2 - Number of ring gear teeth 3 - Manufacturing numbers 4 - Matching gear set number 5 - Number of pinion teeth 6 - Date code 7 - Indicates genuine Spicer parts 8 - Heat code SPICER 41-8 127381 NL2 OF 17 8-41 127428 SPICER 17 G ...Oct 12, 2017 · Ever since changing the gear ratio on my Dana 44 rear diff a couple of years ago from 3.55 to 4.10, the gears whine when going around 35-55 MPH with just enough throttle to maintain that speed. Not a loud whine, just enough to be annoying. When accelerating or decelerating in this range the whine disappears. At speeds above or below 35-55 there ...